Kalessi Bathroom ware

Shower base installation
instructions

Defects should be recognized and checked before installing

1. The products should not possess cracks and holes. 

2. No scratches on visible surfaces. 

3. Twisting and distortion are prohibited. 

4. When leveled, the Shower base should drain water.

The checks are necessary before the installation process as the manufacturer has no control over the storage and transportation once it leaves the warehouse.

If the defect can be identified before installation, then the responsibility doesn’t lie on the manufacturer to bear the cost of removal or replacement of the shower

INSTALLATION OF THE SHOWER BASE WILL BE TREATED AS ACCEPTANCE OF QUALITY

Kalessi floor installation

  1. All joints should be checked and ensure that there is no rot and the soundness of the floor.
  2. Cut hole in floor 15mm bigger after measuring the support ring on the underside of the base, so that further adjustment can be done. 
  3. A 12mm notched trowel, a 10mm 4: 1 mortar mix, or silicone is required to install the base on the cemented surface. The underside of the base must be fully supported over the entire surface area (Excluding waste). 

Test the base after the base is in position, Large droplets of water will remain due to surface tension on the surface however large pools should not be obvious.  Pouring a bucket of water will test the water shower.

Instructions for shower base installations.

1. Concrete floor installation

2. 300mm x 300mm is the maximum measurement for the void area in the slab

3. Support ring span is 300mm maximum,150mm from the center of the outlet in all directions.

4. A smart pan is used for the base to directly sit on it. 

5. A 12mm notched trowel, a 10mm 4: 1 mortar mix, or silicone is needed to install the base on the cemented surface. The underside of the base must be fully supported over the entire surface area (Excluding waste ).

Test the base after the base is in position; large droplets of water will remain due to surface tension on the surface however, large pools should not be obvious.

Installation instructions for flush to floor can be downloaded from

Waste Outlets

It is recommended to run a good amount of silicone to the underside of the outlet flange and position it in the base. If the outlet is required to be installed on your shower base. The black rubber ring is to be placed against the underside position of the base and tighten the nut into position Excess silicone around the outlet flange and shower base should be cleaned. 

Silicone Installation

The base area should be flat and level when using silicone for installation. To ensure full support of the shower base silicone must be placed 100 mm apart.

Cleaning (Avoid abrasive cleaner)

To preserve the high luster, it should be cleaned with a soft cloth material along with soapy water to avoid surface build-up issues. In case of accidental abrasion, silicon-based polishing must be done

Installer – A copy of the installation should be left for the end-user. Non-performance of instructions will void the warranty.

Defects should be recognized and checked before installing

1. The products should not possess cracks and holes. 

2. No scratches on visible surfaces. 

3. Twisting and distortion are prohibited. 

4. When leveled, the Shower base should drain water.

The checks are necessary before the installation process as the manufacturer has no control over the storage and transportation once it leaves the warehouse.

If the defect can be identified before installation, then the responsibility doesn’t lie on the manufacturer to bear the cost of removal or replacement of the shower

INSTALLATION OF THE SHOWER BASE WILL BE TREATED AS ACCEPTANCE OF QUALITY

Kalessi floor installation

  1. All joints should be checked and ensure that there is no rot and the soundness of the floor.
  2. Cut hole in floor 15mm bigger after measuring the support ring on the underside of the base, so that further adjustment can be done. 
  3. A 12mm notched trowel, a 10mm 4: 1 mortar mix, or silicone is required to install the base on the cemented surface. The underside of the base must be fully supported over the entire surface area (Excluding waste). 

Test the base after the base is in position, Large droplets of water will remain due to surface tension on the surface however large pools should not be obvious.  Pouring a bucket of water will test the water shower.

Instructions for shower base installations.

1. Concrete floor installation

2. 300mm x 300mm is the maximum measurement for the void area in the slab

3. Support ring span is 300mm maximum,150mm from the center of the outlet in all directions.

4. A smart pan is used for the base to directly sit on it. 

5. A 12mm notched trowel, a 10mm 4: 1 mortar mix, or silicone is needed to install the base on the cemented surface. The underside of the base must be fully supported over the entire surface area (Excluding waste ).

Test the base after the base is in position; large droplets of water will remain due to surface tension on the surface however, large pools should not be obvious.

Installation instructions for flush to floor can be downloaded from

Waste Outlets

It is recommended to run a good amount of silicone to the underside of the outlet flange and position it in the base. If the outlet is required to be installed on your shower base. The black rubber ring is to be placed against the underside position of the base and tighten the nut into position Excess silicone around the outlet flange and shower base should be cleaned. 

Silicone Installation

The base area should be flat and level when using silicone for installation. To ensure full support of the shower base silicone must be placed 100 mm apart.

Cleaning (Avoid abrasive cleaner)

To preserve the high luster, it should be cleaned with a soft cloth material along with soapy water to avoid surface build-up issues. In case of accidental abrasion, silicon-based polishing must be done

Installer – A copy of the installation should be left for the end-user. Non-performance of instructions will void the warranty.

Leave a Reply

Your email address will not be published.